Steel Sliding Gate Gear Rack
Tianjin OuNaiDa Transmissions Technology Co., Ltd. is one of the leading manufacturers and suppliers of steel sliding gate gear rack in China. If you're going to buy high quality steel sliding gate gear rack, welcome to get more information from our factory. Also, custom service is available.
Steel Sliding Gate Gear Rack
M4 and M6 solid steel racks for automatic sliding gate drives
A steel rack is the straightforward choice when the gate drive sees repeated impact, outdoor grit or a heavier working load. The rectangular steel body keeps the tooth line stiff, and replaceable mounting bolts make the installation familiar to gate builders and service technicians. This Steel Sliding Gate Gear Rack is widely used in automatic door systems to ensure smooth and accurate door movement. It is installed on the sliding door, and the gear is installed on the motor. When the motor is running, the gear will rotate and slide the sliding door in one direction to achieve flexible opening and closing. The rack is made of stainless steel, C45 and other steel materials, and provides coating, grinding and other surface treatments. It has excellent strength,durability and can withstand heavy loads. It has fixed pre-holes to slide securely into the grooves of the next section of rack, making it easy to install and maintain.
Solid steel sliding gate rack with mounting bolt and reference geometry.
Built for firm engagement. The rack is intended for a matching spur pinion. Confirm module, pressure angle, pinion face width and mounting height before ordering a replacement section.
Product name: Steel Sliding Gate Gear Rack for Gate Openers
Short description: Solid M4 and M6 steel gear racks for automatic sliding gate drives, available in nominal 1 m and 2 m sections with multiple cross-sections, mounting bolts and zinc or galvanized surface protection.
SEO title: Steel Sliding Gate Gear Rack Manufacturer | M4 & M6
Meta description: M4 and M6 steel sliding gate gear racks in 1 m and 2 m sections. Multiple cross-sections, mounting bolts, corrosion-protected finishes, matched pinions and export packing.
Keywords: steel sliding gate gear rack; M4 steel gate rack; M6 gate rack; gate opener rack; galvanized gear rack; sliding gate rack manufacturer
Features
1. High strength: Each tooth of this Steel Sliding Gate Gear Rack adopts a compact structural design and has been hardened. It meshes with gears or pinions on the gate to ensure reliable and synchronous operation.
2. Various sizes: This rack can be 500mm, 1018mm, 1998mm, 2010mm or OEM length. It is available in a variety of length, width, height and tooth profile options to accommodate different gate sizes and load carrying capacities.
3. Anti-corrosion: The rack supports a variety of surface treatment processes, including white zinc coating, spraying with natural pigments and paint, etc. This makes its surface covered with a film or paint to isolate the total moisture in the air and avoid corrosion.
4. Easy to install: Its simple structure and smooth appearance make it easy to disassemble and reinstall after long-term use, ensuring safe and efficient use.
Will fit most brand of gate openers like
PY600AC, SL600AC, PY800AC, SL800AC, PY1400AC, SL1400AC, and PY1800.
For the rack surface treatment
common used white zinc, natural color and paint.
For the length
it can be 500mm, 1018mm, 1998mm, 2010mm, or OEM length. For the width and height, the type includes 8x30, 9x30, 10x30, 11x30, 12x30, 15x30, 20x20, 22x22, 25x25, 30x30, 20x26.


Steel Rack Size Range
Most sliding gate openers use M4. M6 is available for selected heavier systems, but it should not be chosen only because the gate is large: the opener pinion must also be M6. Lengths and weights below are nominal working references.
|
Module |
Section A x H (mm) |
Nominal length |
kg/m |
|
M4 |
8 x 30 |
1 m / 2 m |
1.75 |
|
M4 |
9 x 30 |
1 m / 2 m |
1.95 |
|
M4 |
10 x 30 |
1 m / 2 m |
2.17 |
|
M4 |
11 x 30 |
1 m / 2 m |
2.36 |
|
M4 |
12 x 30 |
1 m / 2 m |
2.55 |
|
M4 |
22 x 22 |
1 m / 2 m |
3.10 |
|
M4 |
30 x 30 |
1 m / 2 m |
5.40 |
|
M6 |
30 x 30 |
1 m / 2 m |
5.50 |
Construction and order options
Solid rectangular steel body with straight teeth for a matching spur pinion.
Nominal 1 m and 2 m sections; 1000/1005 mm references are common in gate projects.
Zinc-finished or galvanized protection selected according to the order and environment.
Mounting bolt sets, matched pinions, project labels and export packing available.
Order drawing. Hole position, bolt style, finish and exact finished length must follow the approved order drawing. Do not release production from the outside section size alone.
STRENGTH IS USEFUL ONLY WHEN THE RACK IS ALIGNED
Application and Installation
Steel sliding gate racks are commonly fitted to warehouse gates, factory entrances, perimeter-control gates and residential systems that use a solid steel drive line. They are also practical for repairs because individual sections and bolt sets can be replaced without changing the complete gate frame.
Installation points
Correct worn wheels, a bent track or a dragging gate before the rack is installed.
Set the pinion parallel to the rack and keep a small working clearance; zero backlash makes the drive noisy and tight.
Bridge every rack joint with a spare rack piece or joining gauge before final tightening.
Run the gate through its full travel by hand, then test at low speed and listen for a change in mesh noise.
Keep the steel teeth lubricated and repair damaged corrosion protection during routine maintenance.

The rack moves with the gate while the opener pinion remains fixed.
Do not use the rack as a rail. The wheels and track support the gate weight. The rack only transfers drive force from the opener pinion.
INSPECTION RECORDS AND COMPLIANCE DOCUMENTS
Quality Assurance and Certificates
Before packing, we check the steel section, module, length, tooth condition, surface finish and bolt set against the confirmed order. Module, length, tooth condition, mounting features and included hardware are reviewed together, because a correct rack with the wrong fastener set still creates an installation problem.
|
Document |
Coverage |
Availability note |
|
CE Certificate of Conformity |
Listed sliding-gate rack models |
Scope and current validity checked before issue |
|
ISO 9001:2015 Certificate |
Quality management system documentation |
Current copy available for customer review |
|
Order documents |
Inspection report, material record or agreed checklist |
Specify required records before production |
CE Certificate of Conformity for the listed sliding-gate rack models.
Document control. CE and ISO documents are supplied according to their applicable scope and current validity. If a project needs a certificate number or inspection record on the shipping documents, state it before the order is released.

A long steel rack is dense enough to damage its own teeth if it slides inside the case. Sections are separated, restrained and packed around the actual length and order weight. Mounting bolts and pinions are identified separately so installers do not mix hardware between projects.
Bundled steel sections with separators to limit tooth-to-tooth contact.
Reinforced wooden cases or pallets for long and heavy export shipments.
Separate counting and labels for bolts, pinions and project-specific accessories.
Packing marks and private labels available when confirmed with the order.
Reinforced wooden cases protect long steel rack sections during export transport.
Fast delivery. Common M4 steel sections may be prepared from stock once the section, length and bolt set are confirmed. M6, special hole patterns, private labels and non-standard packing follow an agreed production lead time.
Gate weight, travel length, opener model and expected operating frequency.
Required module, steel section, nominal length and quantity.
Surface finish, bolt set, matched pinion, labels and shipping destination.
Drawing or clear photographs for replacement and non-standard work.
Inquiry: Email sales@tjond.com with the subject "Steel sliding gate gear rack inquiry".

Why choose us?
- We offer a broad range of Sliding Gate Gear Rack products to meet our clients' diverse needs.
- We look forward to establishing good and long-term business relationships with you.
- Our Sliding Gate Gear Rack products are competitively priced without compromising on quality.
- The company has become a member of China's Steel Sliding Gate Gear Rack equipment industry with the purpose of being sincere and casting the future.
- We offer flexible payment options for our Sliding Gate Gear Rack products to meet our clients' needs.
- As a means to motivate employees to work hard, incentive plays an increasingly important role in enterprise management.
- As a manufacturer and supplier, we offer competitive pricing for our Sliding Gate Gear Rack products.
- We continue to strengthen our technology development capacity building.
- We provide a fast and efficient service for our Sliding Gate Gear Rack products, ensuring minimal downtime for our clients.
- We are advancing at full speed towards a quality and efficiency enterprise, showing our strong strength at all times.
Hot Tags: steel sliding gate gear rack, China steel sliding gate gear rack manufacturers, suppliers, factory, ratchet rack and pinion, 6 Eyes Sliding Gate Gear Rack, double rack and pinion, Steel Sliding Gate Gear Rack, Nylon Gear Rack, metal rack and pinion
You Might Also Like
Send Inquiry















