
Oldham Coupling For Ball Screw Drives
Tianjin OuNaiDa Transmissions Technology Co., Ltd. is one of the leading manufacturers and suppliers of oldham coupling for ball screw drives in China. If you're going to buy high quality oldham coupling for ball screw drives, welcome to get more information from our factory. Also, custom service is available.
--- title: "SZHK Series Oldham Coupling For Ball Screw Drives" slug: coupling/szhk-oldham-coupling type: product week: W47 date: 2026-11-17 category: Coupling main_image: media-output/W47-p4-szhk-oldham-coupling.png meta_description: "SZHK cross slider (Oldham type) shaft couplings, OD 20 to 70 mm, bore 4 to 37 mm. Allowable parallel offset 1.2 to 4 mm. Full torque, speed and misalignment table." keywords: SZHK coupling, Oldham coupling, cross slider coupling, SZHK-D20, SZHK-D25, SZHK-D32, SZHK-D40, SZHK-D50, ball screw coupling, stepper motor coupling ---
A machine builder sent back three cracked beam couplings from the same axis in two months. Each time the motor plate had been re-shimmed, the screw re-aligned, and the coupling replaced. Each time it cracked again.
The dial indicator told the story: the motor shaft sat 0.6 mm off the screw centre, and the support bearing housing could not be moved without re-machining.
A beam coupling bends to absorb offset. Bend it 0.6 mm at a few thousand rpm and it fatigues. A cross slider coupling does not bend at all - the centre disc slides. That axis has run on an SZHK since.
How the SZHK Works
Three parts: two hubs that clamp onto the shafts, and a centre disc between them. Each face of the disc carries a tongue, and the two tongues are at 90 degrees to each other. Each tongue engages a slot in its hub.
When the shafts are offset, the disc slides along both slots as it rotates. Torque goes through the tongues; misalignment is taken by sliding, not by flexing metal. Our catalogue calls this the cross-shaped coupling; the wider industry name is the Oldham coupling.
Full Specification Table
| Model | Bore d1/d2 (mm) | OD D | Length L | Clamp screw | Screw torque (N·m) | Rated torque (N·m) | Max. torque (N·m) | Max. speed (rpm) | Torsional stiffness (N·m/rad) | Parallel offset (mm) | Angular (°) | Axial (mm) |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| SZHK-D20*25 | 4 - 10 | 20 | 25 | M3 | 1.5 | 1.5 | 3 | 7000 | 60 | 1.2 | 3 | ±0.2 |
| SZHK-D20*33 | 4 - 10 | 20 | 33 | M3 | 1.5 | 1.5 | 3 | 7000 | 60 | 1.2 | 3 | ±0.2 |
| SZHK-D25*28 | 5 - 12 | 25 | 28 | M3 | 1.5 | 2 | 4 | 6100 | 130 | 1.6 | 3 | ±0.2 |
| SZHK-D25*39 | 5 - 12 | 25 | 39 | M3 | 1.5 | 2 | 4 | 6100 | 130 | 1.6 | 3 | ±0.2 |
| SZHK-D32*45 | 6 - 15 | 32 | 45 | M4 | 3.5 | 5 | 9 | 4800 | 275 | 2 | 3 | ±0.2 |
| SZHK-D34*35 | 6 - 17 | 34 | 35 | M4 | 3.5 | 5 | 9 | 4800 | 275 | 2 | 3 | ±0.2 |
| SZHK-D40*50 | 8 - 20 | 40 | 50 | M5 | 8 | 10 | 20 | 3600 | 520 | 2.7 | 3 | ±0.2 |
| SZHK-D44*46 | 8 - 22 | 44 | 46 | M5 | 8 | 13 | 26 | 3600 | 520 | 3 | 3 | ±0.2 |
| SZHK-D50*58 | 10 - 26 | 50 | 58 | M6 | 13 | 19 | 37 | 3000 | 800 | 3 | 3 | ±0.2 |
| SZHK-D55*58 | 10 - 28 | 55 | 58 | M6 | 13 | 25 | 50 | 3000 | 1200 | 3.2 | 3 | ±0.2 |
| SZHK-D63*71 | 14 - 35 | 63 | 71 | M8 | 28 | 33 | 65 | 2600 | 1200 | 3.5 | 3 | ±0.2 |
| SZHK-D70*77 | 16 - 37 | 70 | 77 | M8 | 28 | 56 | 110 | 2500 | 1200 | 4 | 3 | ±0.2 |
Bore range is the minimum to maximum standard bore; d1 and d2 can differ, for example 8 mm motor to 10 mm screw. Clamp screws are tightened to the "screw torque" value - not the coupling's rated torque.
Things That Shorten Coupling Life
Using the misalignment numbers as a target. The 1.2 to 4 mm offset figures are limits, each assuming that is the only misalignment present. In practice there is always some offset, some angle and some axial movement together. Manufacturers commonly advise halving each allowance when misalignments combine, and keeping each below about one third of its limit for long service life. An Oldham coupling forgives a bad installation; it does not make one free.
Picking by bore, not by torque. A D20 takes up to a 10 mm bore but is rated 1.5 N·m. Plenty of motors with a shaft that fits a D20 produce more peak torque than that. Size the coupling on motor peak torque, then check the bore fits - not the other way round.
Ignoring temperature on a polymer disc. The centre disc material sets the torque limit, and polymer loses strength as it warms. Next to a hot motor or in an enclosed cabinet, derate the torque or step up a size.
Expecting zero backlash at large offsets. The disc must slide, so it carries a small running clearance in the slots. With the shafts well aligned this is negligible; at large offset it shows up as lost motion on reversal. For axes that need true zero backlash at high positioning accuracy, a disc or slit coupling with good alignment is the better choice.
Where the SZHK Fits
- Stepper and servo motors driving ball screws where the motor mount cannot be finely aligned
- Retrofits with an existing offset you cannot machine out
- Pumps, feeders and conveyors with parallel shaft offset
- Assemblies that need quick separation: the hubs pull apart off the disc without moving the motor
For a full axis, match the coupling to the screw end and support unit - see our ball screw support units and the guide on nut housing and coupling selection. Other designs are in our coupling range, including clamping flexible shaft couplings.
What to Send Us
1. Motor shaft and driven shaft diameters (d1, d2) 2. Motor peak torque and maximum speed 3. Space available: maximum OD and length 4. Measured offset, if known 5. Operating temperature 6. Quantity
OEM and ODM accepted. Samples available.
Precision Motion Components | Empowering Global Intelligent Manufacturing
Hot Tags: oldham coupling for ball screw drives, China oldham coupling for ball screw drives manufacturers, suppliers, factory, coupling bearings, coupling development, coupling example, coupling guards, coupling module, coupling monitoring system
Previous
No InformationYou Might Also Like
Send Inquiry










