
Low Profile Linear Guide Block
Tianjin OuNaiDa Transmissions Technology Co., Ltd. is one of the leading manufacturers and suppliers of low profile linear guide block in China. If you're going to buy high quality low profile linear guide block, welcome to get more information from our factory. Also, custom service is available.
--- title: "HGL Series Low Profile Linear Guide Block" slug: linear-guideways/hgl-low-profile-linear-guide-block type: product week: W47 date: 2026-11-17 category: Linear Guideways main_image: media-output/W47-p1-hgl-low-profile-linear-guide.png meta_description: "HGL-CA/HA low profile ball linear guide blocks, sizes 15 to 55. Assembly height 3 to 10 mm lower than HGH on the same rail, same dynamic load rating. Full dimension and load table." keywords: HGL linear guide, HGL15CA, HGL25CA, HGL25HA, HGL30CA, HGL35CA, HGL45CA, HGL55CA, low profile linear guide block, low assembly linear guideway ---
A buyer redesigning a pick-and-place axis sent us a drawing with one problem circled in red: the moving plate sat 10 mm too high to clear an overhead frame. The guideway was an HGH45CA. Moving the frame meant re-certifying the cell. Machining the base meant scrapping a casting.
He did not need either. He needed the same rail with a lower block.
That is what the HGL series is. Same HGR rail, same block width, same bolt pattern on top - with the assembly height cut by 3 to 10 mm depending on size.
HGL vs HGH: What Changes and What Does Not
Taken directly from our catalogue tables for the two series:
| Size | HGH-CA height H (mm) | HGL-CA height H (mm) | Lower by (mm) | Block width W (mm) | Dynamic load C (kN), both series |
|---|---|---|---|---|---|
| 15 | 28 | 24 | 4 | 34 | 11.38 |
| 25 | 40 | 36 | 4 | 48 | 26.48 |
| 30 | 45 | 42 | 3 | 60 | 38.74 |
| 35 | 55 | 48 | 7 | 70 | 49.52 |
| 45 | 70 | 60 | 10 | 86 | 77.57 |
| 55 | 80 | 70 | 10 | 100 | 114.44 |
The dynamic load rating is identical size for size. The rail is identical too - width, height, hole pitch and weight per metre all match. So a height problem on an HGH axis can usually be solved with an HGL block on the existing rail.
The block itself is lighter: 0.14 kg against 0.18 kg at size 15, 3.25 kg against 4.17 kg at size 55.
Note there is no size 20 in the HGL range. If your axis runs on a 20 mm rail, HGL is not an option - look at the EGH20SA low profile block instead.
Full Dimension and Load Table
CA = standard length block. HA = long block on the same rail (sizes 25 to 55).
| Model | H | W | B x C (mounting holes) | Block length L | Mounting thread | Rail WR x HR | Rail bolt | C (kN) | C0 (kN) | MR / MP / MY (kN-m) | Block (kg) | Rail (kg/m) |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| HGL15CA | 24 | 34 | 26 x 26 | 61.4 | M4x4 | 15 x 15 | M4x16 | 11.38 | 16.97 | 0.12 / 0.10 / 0.10 | 0.14 | 1.45 |
| HGL25CA | 36 | 48 | 35 x 35 | 84 | M6x6 | 23 x 22 | M6x20 | 26.48 | 36.49 | 0.42 / 0.33 / 0.33 | 0.42 | 3.21 |
| HGL25HA | 36 | 48 | 35 x 50 | 104.6 | M6x6 | 23 x 22 | M6x20 | 32.75 | 49.44 | 0.56 / 0.57 / 0.57 | 0.57 | 3.21 |
| HGL30CA | 42 | 60 | 40 x 40 | 98.4 | M8x10 | 28 x 26 | M8x25 | 38.74 | 52.19 | 0.66 / 0.53 / 0.53 | 0.78 | 4.47 |
| HGL30HA | 42 | 60 | 40 x 60 | 121.4 | M8x10 | 28 x 26 | M8x25 | 47.27 | 69.16 | 0.88 / 0.92 / 0.92 | 1.03 | 4.47 |
| HGL35CA | 48 | 70 | 50 x 50 | 112.4 | M8x12 | 34 x 29 | M8x25 | 49.52 | 69.16 | 1.16 / 0.81 / 0.81 | 1.14 | 6.30 |
| HGL35HA | 48 | 70 | 50 x 72 | 138.2 | M8x12 | 34 x 29 | M8x25 | 60.21 | 91.63 | 1.54 / 1.40 / 1.40 | 1.52 | 6.30 |
| HGL45CA | 60 | 86 | 60 x 60 | 137.4 | M10x17 | 45 x 38 | M12x35 | 77.57 | 102.71 | 1.98 / 1.55 / 1.55 | 2.08 | 10.41 |
| HGL45HA | 60 | 86 | 60 x 80 | 169.2 | M10x17 | 45 x 38 | M12x35 | 94.54 | 136.46 | 2.63 / 2.68 / 2.68 | 2.75 | 10.41 |
| HGL55CA | 70 | 100 | 75 x 75 | 166.7 | M12x18 | 53 x 44 | M14x45 | 114.44 | 148.33 | 3.69 / 2.64 / 2.64 | 3.25 | 15.08 |
| HGL55HA | 70 | 100 | 75 x 95 | 204.8 | M12x18 | 53 x 44 | M14x45 | 139.35 | 196.2 | 4.88 / 4.57 / 4.57 | 4.27 | 15.08 |
Dimensions in mm. Rail hole pitch: 60 mm (sizes 15, 25), 80 mm (30, 35), 105 mm (45), 120 mm (55).
Three Mistakes We See on HGL Retrofits
Re-using the old screws at sizes 15 and 25. The top mounting thread is shallower on the low block: M4x4 on HGL15 against M4x5 on HGH15, and M6x6 on HGL25 against M6x8 on HGH25. A screw sized for the HGH thread depth can bottom out in the HGL block and leave the plate loose while the torque wrench clicks. From size 30 up the thread depth is the same in both series.
Lowering one side only. Swap every block on the axis, and on a gantry, both rails. Then check what else references the table height - the ball screw nut housing, a rack, a cable track bracket. Lowering the guide by 10 mm and leaving the nut housing where it was puts a bending load into the screw.
Comparing load ratings across catalogues without checking the edition. HIWIN's current catalogue lists higher ratings for HGL blocks than the figures above (for example HGL25CA at 34.9 kN dynamic). Our table follows the earlier rating basis, which matches HIWIN's previous published values for the same blocks. Neither number is wrong. Just compare like with like when one supplier's datasheet looks 30% stronger than another's for the same model.
When HGL Is the Right Choice
- Retrofits where the moving plate has to drop without touching the machine base
- Compact automation cells and vertical axes with tight overhead clearance
- Designs already on HGR rail that need lower stack height, not more load
When height is not the constraint, the standard HGH block is the more common choice, and the flanged HGW20HC suits mounting from underneath.
What to Send Us
1. Block model, or the height you need to reach 2. Rail length and number of rails 3. Blocks per rail 4. Accuracy and preload class if specified on your drawing 5. Whether this replaces an existing HGH block 6. Quantity
We cut rails to length and supply blocks pre-fitted to the rail on request. Browse the full linear guideway range or ask for a drawing.
OEM and ODM accepted. Samples available.
Precision Motion Components | Empowering Global Intelligent Manufacturing
Hot Tags: low profile linear guide block, China low profile linear guide block manufacturers, suppliers, factory, gear engraving, linear guideway assemblies, linear guideway energy efficient, linear guideway rollers, linear guideway sustainable, linear motion systems
Previous
No InformationYou Might Also Like
Send Inquiry










